|
| |
|
| |
 |
|
|
| |
|
| |
| |
| SUN BLOC FORMULA PROTECTANT |
| |
|
 |
AUTOGUARD Protectant/Beautifier has a unique polymer silicone formula that helps block out the
sun's harmful rays while restoring luster and bringing out the color of leather, vinyl rubber and plastic.
AUTOGUARD Protectant is easy to use and is non-flammable and odorless. It also protects against
abrasion and reduces dirt attraction by eliminating static electricity.
Material Safety Data
Sheets
Specifications
|
| |
|
| AUTOGUARD QUICK FLAT FIX |
| |
|
 |
AUTOGUARD Quick Flat Fix - Tire Sealer and inflator seals and inflates most
common punctures instantly and effectively. AUTOGUARD Quick Flat Fix is safe for use on all passenger car and utility tires, tube and tubeless. AUTOGUARD Quick Flat Fix contains a Butyl Latex Sealant as its active ingredient. AUTOGUARD Quick Flat Fix is a temporary repair only, the punctured tire should be permanently repaired by a professional as soon as possible. If possible, remove object that caused flat. Shake can well before using. Remove valve stem extension if one exists.
1) For AUTOGUARD Quick Flat Fix with Hose - Tire valve should be in a 4 to 8 o'clock position. Screw adapter hose onto tire valve tightly. Remove cap, hold can upright and push button to seal and inflate tire.
2) For AUTOGUARD Quick Flat Fix with Cone - Tire valve should be in a 6 o'clock position. Push adapter cone firmly onto tire valve stem. Quick Flat Fix will automaticcally begin to seal and inflate tire.
Use entire contents to fill car and truck tires. Remove hose/cone from valve stem and drive 2 to 4 miles immediately to provide maximum distribution of sealant. At the first opportunity, have tire examined by a professional. Check tire for correct pressure.
DANGER: Do not attempt to repair tire or remove, have repaired while inflated. It is important that all gas be
expelled from tire in open area, not subject to fire.
Material Safety Data
Sheets
Specifications |
| |
|
| AUTOGUARD CARBURETOR CLEANER |
| |
|
 |
Vehicles with carburetors build up "sludge", "varnish", and other deposits
due to poor combustion of fuel. These deposits reduce fuel combustion and cause valves to stick. All the
linkages on a carburetor will stick causing the carburetor to run inefficiently.
AUTOGUARD Carburetor
Cleaner is a blend of selected solvents, carefully formulated to maximize cleaning power. Difficult
deposits are eliminated quickly.
Use in well ventilated area. Insert extension tube into valve button. Avoid contact with car finish.
CARBURETOR AND LINKAGE: With engine off, remove air cleaner. Start engine and set at fast idle.
Spray AUTOGUARD Carburetor Cleaner on exterior surface of carburetor, including linkage. Also spray
in short bursts around inside of carburetor. Allow engine to run for one minute and then repeat procedure
for inside and outside of carburetor.
PCV VALVE: With engine off, disconnect hose from valve. Insert extension tube into valve opening and
spray while working valve back and forth. Start engine and spray three or four short burst.
AUTOMATIC CHOKE: With engine off, spray ends of choke valve while opening and closing manually.
Also spray piston and cylinder.
WARNING: This product is highly flammable and user should exercise caution
Material Safety Data Sheets
Specifications |
| |
|
| AUTOGUARD DE-ICER |
| |
|
 |
AUTOGUARD De-Icer is used to remove frost or ice from
windshields. AUTOGUARD De-Icer is an aerosol, its active ingredient is methanol with additional
ingredients being ethylene glycol, other alcohols and water. When the De-Icer is sprayed on, the
methanol soaks into the frozen material and rapidly lowers its melting point. This allows the ice to
become a soft, slush-like mixture even at below-freezing temperatures. This mixture can be removed
with windshield wipers or a windshield-cleaning tool. If AUTOGUARD De-Icer is applied in
advance, it will retard ice formation and fogging on inside of windows.
Material Safety Data Sheets
Specifications |
| |
|
| AUTOGUARD
POWER STEERING FLUID |
| |
|
 |
AUTOGUARD Service Fill Power Steering Fluid helps maintain efficiency, performance and the
condition of power steering units. Helps prevent leakage and helps prevent squealing under severe
conditions. Will not clog or foam. Helps prevent corrosion, oxidation and wear. For year round use.
Material Safety Data
Sheets
Specifications
|
| |
|
| |
|
| HIGH TEMPERATURE
Lithium Complex Grease
AUTOMOTIVE, INDUSTRIAL and COMMERCIAL |
| |
|
 |
Features
(1) Premium quality lithium complex multi-purpose grease.
(2) Water insoluble and water washout resistant
(3) Superior wheel bearing and chassis performance
(4) Full additive package: EP/antiwear, rust and oxidation inhibited
(5) Extremely versatile mulit-purpose grease
(6) NLGI Service Classification GC-LB
(7) Superior lubrication protection in severe duty automotive, trucking, industrial, mining,
construction equipment and marine applications.
Material Safety Data Sheets
Specifications |
| |
|
| |
| |
|
| AUTOGUARD -HEAVY DUTY BRAKE FLUID |
| |
|
 |
This product exceeds all requirements of the Federal Motor Vehicle Safety Standard as published
in December 16, 1976 , Federal Register for DOT 3 Motor Vehicle Brake Fluid. |
| Typical Characteristics |
DOT 3 |
SAE J1703 |
| Original Equilibrium Reflux:Boiling Point degC |
205 min |
205 min. |
| Boiling Point degF |
401 min. to 447 max. |
401 min.to483 max |
Wet Equilibrium Reflux:
Boiling Point degC |
140 min. |
140 min. |
| Viscosity @ 100˚C, cSt |
1.5 min. |
1.5 min. |
| @-40˚C, cSt |
1500 max. |
1800 max. |
| PH |
7-11.5 |
7-11.5 |
Fluid Stability:
High Temp Stability
degC change |
3 max. |
5 max. |
Chemical Stability
degC change |
3 max. |
5 max. |
| Corrosion (wt change), mg/cm- Tinned iron |
0.2 max. |
0.2 max. |
| Steel |
0.2 max |
0.1 max |
| Aluminum |
0.1 max |
0.1 max |
| Cast iron |
0.2 max |
0.2 max |
| Brass |
0.4 max |
0.4 max |
| Copper |
0.4 max |
0.4 max |
| Fluidity at low temperatures:Inversion time @ -40˚C, sec |
10 max. |
10 max. |
| Inversion time @ -50˚C, sec |
35 max. |
35 max. |
| Evaporation at 100˚C:Loss in weight, wt% |
80 max. |
80 max. |
| Pour point of residues, deg C |
-5 max. |
-5 max. |
| Water tolerance:Inversion time @ -40˚C, sec |
10 max. |
10 max. |
| Sedimentation @ 60˚C, vol% |
0.15 max |
0.15 max |
| Compatiblity:Sedimentation @ 60˚C, vol% |
0.05 max. |
0.05 max. |
| Resistance to oxidation:Cast iron (wt. change), mg/cm2 |
0.3 max. |
0.3 max. |
| Aluminum (wt. change), mg/cm2 |
0.05 max. |
0.05 max. |
Effect on rubber cups:Synthetic rubber (70˚C
base diameter increase, mm |
0.15-1.4 |
0.15-1.4 |
| Hardness decrease (IRHD) |
10 max. |
10 max. |
Synthetic rubber (120˚C)
base diameter increase, mm |
0.15-1.4 |
0.15-1.4 |
| Hardness decrease (IRHD) |
15 max. |
15 max. |
| Stroking Properties: |
Pass |
Pass |
Material Safety Data
Sheets
Specifications
|
| |
|
| |
|
| AUTOGUARD
-20 Degree
WINDSHIELD WASHER FLUID |
| |
|
 |
AUTOGUARD Windshield Washer fluid is a high quality product made from Methanol and
other additives. Cleans as well as removes salt spatter. road film and bugs. Prevents freezing
to -20˚ F.
Typical Characteristics
Methanol
Aqua Ammonia (.03% by wt)
Blue Tint
Material Safety Data Sheets
Specifications |
|
| AUTOGUARD CLEAR VISION BUG WASH |
| |
 |
AUTOGUARD Bug Wash and Zero˚ Fluid are economical, warm climate, windshield
washer fluids, developed to aid in the removal of road film, bugs, and other matter that
may obscure vision.
Material Safety Data Sheets
Specifications |
|
| |
| AUTOGUARD OIL TREATMENT |
| |
 |
Older worn engines will develop low compressions, blowby, smoking
noise and oil burning as symptoms of age. AUTOGUARD Oil Treatment will help in reducing, if not
alleviating, these symptoms. AUTOGUARD Oil Treatment contains a synthetic polymer and
additives which will improve the viscosity index of motor oil. AUTOGUARD Oil Treatment will coat
moving parts with a tough film that decreases friction and increases power.
Add one bottle of AUTOGUARD Oil Treatment with every oil change. Also, add one bottle between
changes whenever oil is added. Allow engine to reach operating temperatures then pour into
crankcase. For badly worn engines add two bottles.
Material Safety Data Sheets
Specifications |
|
| AUTOGUARD FUEL INJECTOR & CARBURETOR CLEANER |
| |
 |
Over a period of time, automotive fuel systems will build up deposits,
sludge & varnish. This build up will cause the engine to run sluggish, hesitate, lose power and reduce
fuel economy. AUTOGUARD Fuel Injector & Carburetor Cleaner is designed to be used to increase
power and fuel economy. AUTOGUARD Fuel Injector & Carburetor Cleaner is a petroleum based
product
Material Safety Data
Sheets
Specifications |
|
| AUTOGUARD Super Concentrated FUEL INJECTOR CLEANER |
| |
 |
Fuel Injector systems are designed to deliver precise amounts of fuel and air to
the combustion chamber of an engine. A major problem that prevents the proper delivery of the fuel air
mixture are deposits, throughout the fuel system. AUTOGUARD Fuel Injector Cleaner is designed to dissolve
all deposits and varnish build-ups in the fuel injectors and fuel system. Fuel injector cleaners may be either
petroleum based or alcohol based. Alcohol based products can dry out o-rings used in fuel injectors.
AUTOGUARD Fuel Injector Cleaner is a petroleum based product. Petroleum based products are more
effective at dissolving deposits that accumulate in the fuel system. AUTOGUARD Fuel Injector Cleaner
contains an ashless non-phosphorous polymeric dispersant for deposit control and a corrosion inhibitor.
AUTOGUARD Fuel Injector Cleaner contains a fluidizer oil and detergent that prevents deposits from
adhering to hot metal surfaces.
Material Safety Data
Sheets
Specifications |
|
| AUTOGUARD ENGINE STOP LEAK |
| |
 |
AUTOGUARD Engine Stop Leak is a specially formulated oil additive
designed to reduce or eliminate oil leaks from old worn out seals and gaskets, that have shrunk due to
temperature or wear. Elastomeric seals contacted by hot oil tend to shrink, harden and become less pliable, as a
result oil begins leaking out. One alternative is to replace all the leaking seals, another is to add
AUTOGUARD Engine Stop Leak. AUTOGUARD Engine Stop Leak contains a synthetic seal swell additive
to swell seals back to their original size and helps them regain pliability. This product contains no solids that
can plug oil filters and small engine oil passage ways.
To stop leaks, add entire contents of bottle to engine oil crankcase (consult owner's manual for fill location). If
leakage does not stop after 100 miles, have the engine examined by a professional ( the seals may be cracked or
broken and should be replaced).
Material Safety Data
Sheets
Specifications |
|
| AUTOGUARD GAS TANK TREATMENT with Antifreeze |
| |
 |
AUTOGUARD Gas Tank Treatment with Anti-freeze is a general
purpose gas additive that absorbs moisture that may be in the fuel line. Note: This product is
recommended for use with carburetor fuel systems.
Add one 12 fl. oz. bottle to tank prior to filling up, this will ensure good mixing of product. Product is
OK to use year round if vehicle is in a high humidity area causing condensation in fuel tank.
Material Safety Data
Sheets
Specifications |
|
| AUTOGUARD GAS TREATMENT |
| |
 |
car will start to knock, sputter and hesitate due to
build up of sludge, gum, varnish and moisture. All of these restrict fuel flow or
contaminate the gasoline. AUTOGUARD Gas Treatment removes sludge, gum,
varnishes and reduces water in the fuel system. AUTOGUARD Gas Treatment
also contains an ingredient that prevents deposits from adhering to hot surfaces.
This removal of contaminates will increase fuel economy, smooth rough idle, and
help stop knocking.
There are two types of gas treatment products: petroleum based and alcohol
based. AUTOGUARD and STP are petroleum based. Stewart Warner is alcohol
based. Petroleum based products are more effective at dissolving deposits in
carburetors. An easy way of distinguishing the two types is to look for the "DANGER: May be fatal or cause blindness if swallowed" statement on the front
label of product containing methanol..
To properly treat the gasoline, add one bottle of AUTOGUARD Gas Treatment
to the fuel tank before filling with gasoline. One bottle treats 15 to 21 gallons.
Material Safety Data Sheets
Specifications |
|
| AUTOGUARD OCTANE BOOSTER |
| |
 |
As cars age, their performance tends to diminish, due to deposits throughout the fuel system. These
deposits will tend to cause low octane gasolines to perform less that desirable. AUTOGUARD Octane
Booster will improve the octane rating of gasoline increasing performance, gas mileage and helps in
stopping knocks and pings. AUTOGUARD Octane Booster does not contain alcohol, therefore will not
damage catalytic converters and oxygen sensors. Good for both leaded and unleaded fuels.
It's Use: Pour entire contents into gas tank. Treats up to 20 gallons.
Material Safety Data
Sheets
Specifications |
|
| AUTOGUARD PENETRATING OIL |
| |
 |
AUTOGUARD Penetrating Oil is a penetrant and lubricant as opposed
to WD40 which is just a lubricant. AUTOGUARD Penetrating Oil is a blend of fast acting super
penetrating solvents that evaporate leaving a thin transparent protective film. AUTOGUARD
Penetrating Oil loosens rust and erosion almost instantly, it quickly penetrates into cracks, crevices
and threads, freeing, bolts, lug nuts and other fasteners. Noticeable squeaks are silenced by friction -
reducing lubricants. AUTOGUARD Penetrating Oil may be used as a cleaner to remove tar, grease,
oil adhesives and grimes, as it cleans it will also protect metals from rust and corrosion.
AUTOGUARD Penetrating Oil has many automotive, home and mechanical applications. Spray
liberally and allow to soak. To protect metal surfaces, do not wipe off.
Material Safety Data Sheets
Specifications |
|
| AUTOGUARD PREMIUM STARTING FLUID |
| |
 |
Engine starting fluids are aerosol products which sprayed into the carburetor or attached to an injection system, will assist starting engines which may be balky due to cold, dampness or under maintenance. Typically starting fluids consist of ethyl ether, blended with other petroleum hydrocarbon. How well a product dispenses the ether in cold weather is an important characteristic. AUTOGUARD
Starting Fluids are effective down to -65˚F, they have low freeze points, high vapor pressure at low temperatures, low flash point, high BTU content and an upper cylinder lubricant for protection. AUTOGUARD Starting Fluid may be used with gasoline engines and some diesel engines. It is not recommended using any starting fluid in diesel engines that have glow plugs. Most passenger car and light truck diesel engines have glow plugs in order to preheat the combustion chamber. The use of starting fluid in engines with glow plugs can cause serious engine damage and possible personal injury. Larger trucks and tractors may not have glow plugs. For example, some tractors do not have glow
plugs and inject starting fluid directly into the manifold. Starting fluid works very well in this type of application.
Always consult the owner's manual to determine the manufacturer's recommendation and whether or not a specific vehicle is equipped with glow plugs. Follow the directions on the can when using any of AUTOGUARD Starting Fluids.
Material Safety Data
Sheets
Specifications |
| |
|
|
| |
| |
|
| AUTOGUARD Anti-Freeze READY to use Coolant |
 |
AUTOGUARD Ready to Use Antifreeze is formulated from ethylene glycol and deionized water. It contains an inhibitor
package designed to assure anti-foaming properties as well as rust and corrosion from brass, copper, solder and aluminum. In view of its low concentration of silicate. AUTOGUARD Ready to Use Antifreeze is recommended for use in automotive, and light and heavy duty engines. It is also appropriate for use with Industrial plant systems requiring antifreeze, rust or corrosion protection. AUTOGUARD Ready to Use Antifreeze also prevents the loss of radiator heat transfer, characteristic when using conventional coolant/antifreeze in aluminum cooling systems.
AUTOGUARD Ready to Use Antifreeze meets the following heavy duty engine manufacturers specifications: |
| |
|
| Federal Specifications A-A-870 |
ASTM D 4985 |
| General Motors GM 1899 (GM6038) for Non-Aluminum |
ASTM D 3306 |
| General Motors 1825 for Aluminum |
SAE J 1034 |
| American Association of Motor Vehicle Administrators |
J.I. Case JIC-501 |
| Cummins 85T8-2 |
TMC of ATA RP-302-A |
| Ford ESE-M97B44-A |
AMC AM-4085 |
| Single-Phase Ethylene Glycol Base Antifreeze/Coolant,wt% |
50% |
| Corrosion Inhibitors and Anti foam Agent, wt% |
1.5 Approx. |
| Water, wt% |
48.5 |
| Color |
Fluorescent Green |
| Specific Gravity at 60/60°F |
1.06-1.08 |
| pH @ 67% SOLN (ASTM D 1207) |
10-11 |
| Reserve Alkalinity @ 20 MLS (ASTM D 1121) |
3 MIN |
| Freeze Point, deg F as is (ASTM D 1177) |
-34 MAX |
| Equilibrium Boiling Point, deg F (ASTM D 1120) |
222 MIN |
|
| Freezing Point |
| 33-1/3% |
IN VOLUME SOLUTION |
0°F |
40% |
IN VOLUME SOLUTION |
-12°F |
| 50% |
IN VOLUME SOLUTION |
-34°F |
60% |
IN VOLUME SOLUTION |
-62°F |
| AUTOGUARD Ready to Use Antifreeze is compatible with major brands. |
|
| |
Material Safety Data Sheets
Specifications |
| |
|
| AUTOGUARD Non-Chlorinated brake Parts cleaner |
 |
Removes Brake Fluid, Oil & Brake Dust Instantly Cleans and Degreases Contains No Chlorinated Solvents Contains No CFC Propellants Leaves No Residue Easy to Use Economical
COMPETITION: Pyroil, CRC, Gunk, Berryman
PRODUCT DESCRIPTION: AUTOGUARD Non-Chlorinated Brake Parts Cleaner is specially formulated to powerfully clean without the use of ozone-depleting chemicals. AUTOGUARD Non- Chlorinated Brake Parts Cleaner rate of evaporation is chemically controlled so that the dissolved oils and contaminates are flushed away, leaving no residue. Helps in stopping disc brake squeal. High volume spray nozzle for quick cleaning.
AUTOGUARD Non-Chlorinated Brake Parts Cleaner may be used on metal brake parts, drums, rotors, calipers, springs, backing plates, etc...it is an all-round degreaser and may be used on flywheels andpressure plates for manual transmissions.
CAUTION: Do not spray on brake pad lining, brake shoe lining and/or clutch plate lining.
THIS PRODUCT IS EXTREMELY FLAMMABLE |
| |
| Typical Characteristics: |
| Contains: Methanol, Toluene, Hexane |
Propellant: C02 |
| Specific Gravity: .764 |
Flash Point: 26˚ F TCC |
| Viscosity: NA (Aerosol Product) |
Appearance: Clear-Colorless to Yellow Liquid |
|
| |
Material Safety Data Sheets
Specifications |
| |
|
| AUTOGUARD Multi Purpose Lithium Grease |
 |
This grease is a very economical multi-purpose grease especially suited for normal temperature/speed conditions and other non-critical service applications, as well as those applications requiring frequent regreasing because of a contaminating environment. Water insoluble.
| |
|
| Typical Characteristics |
|
| Code |
5251 |
| NLGI Consistency Number |
2 |
| Thickener |
Lithium Stearate |
| Texture |
Smooth |
| Color, Observed |
Dark Amber |
| Worked 60 Penetration, D-217 |
|
| Dropping Point, D-566, F(C) |
|
| Wheel Bearing Leakage, D-1263,rating |
|
| Approximate Temperature Range, F(C) |
|
| |
|
| PROPERTIES OF OIL: |
|
| VISCOSITIES: |
|
| @ 100˚C, cSt |
11.8 |
| @ 40˚C,cSt |
151 |
| @ 210˚F, SUS |
12.2 (67) |
| @ 100˚F, SUS |
174 (807) |
| Viscosity Index |
50 |
| |
|
Material Safety Data Sheets
Specifications |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
