|
| |
|
| |
 |
|
|
| |
|
| |
|
|
|
| |
|
Warren Chemical products |
| |
|
| |
| HD DOT 3 Brake Fluid |
| |
|
 |
This product exceeds all requirements of the Federal Motor Vehicle Safety Standard as published in December 16, 1976, Federal Register for DOT 3 Motor Vehicle Brake Fluid.
Material Safety Data Sheets |
| |
|
| Power Steering Fluid |
| |
|
 |
Warren Power Steering Fluid helps maintain efficiency, performance and the condition of power steering units. Helps prevent leakage and helps prevent squealing under severe conditions. Will not clog or foam. Helps prevent corrosion, oxidation and wear.
Material Safety Data Sheets |
| |
|
| Quick Flat Fix |
| |
|
 |
Part No. 13850 12oz. Cone Fill 12/case Part No. 13812 12oz. Hose Fill 12/case Seals and Inflates Easy to Use; Economical Temporarily Repairs Punctures To Get Vehicle Back On The Road Safe Non-Toxic Latex Sealant Contains A Warning Label (Propellant is Flammable) Competition: Gunk (Radiator Specialty), Gold Eagle, TMP, Super X. Product Description: Warren Quick Flat Fix – Tire Sealer and inflator seals and inflates most common punctures instantly and effectively. Warren Quick Flat Fix is safe for use on all passenger cars and utility tires, tube and tubeless. Warren Quick Flat Fix contains a Butyl Latex Sealant as its active ingredient. Warren Quick Flat Fix is a temporary repair only, and the punctured tire should be permanently repaired by a professional. If possible, remove object that caused flat. Shake can well before using. Remove valve stem extension if one exists.
1) For Warren Quick Flat Fix with Hose – Tire valve should be in a 4 to 8 o’clock position. Screw adapter hose onto tire valve tightly. Remove cap, hold can upright and push button to seal and inflate tire.
2) For Warren Quick Flat Fix with Cone – Tire valve should be in 6 o’clock position. Push adapter cone firmly onto tire valve stem. Quick Flat Fix will automatically begin to seal and inflate tire.
Use entire contents to fill car and truck tires. Remove hose/cone from valve stem and drive 2 to 4 miles immediately to provide maximum distribution of sealant. At the first opportunity, have tire examined by a professional. Check tire for correct pressure.
DANGER: Do not attempt to repair tire or remove, have repaired while inflated. It is important that all gas be expelled from tire in open are, not subject to fire.
Material Safety Data Sheets |
| |
|
| Brake Parts Cleaner |
| |
|
 |
Removes brake fluid, oil & brake dust. Instantly cleans and degreases. Contains no chlorinated solvents, CFC propellants, and leaves no residue. Easy to use and economical.
Competition: Pyroil, CRC, Gunk, Berryman Product Description: Warren Non-Chlorinated Brake Parts Cleaner is especially formulated to powerfully clean without the use of ozone-depleting chemicals. Warren Non-Chlorinated Brake Parts Cleaner rate of evaporation is chemically controlled so that the dissolved oils and contaminates are flushed away, leaving no residue. Helps in stopping disc brake squeal. High volume spray nozzle for quick cleaning.
Warren Non-Chlorinated Brake Parts Cleaner may be used on metal brake parts, drums, rotors, calipers, springs, backing plates, etc…it is an all-round degreaser and may be used on flywheels and pressure plates for manual transmission.
Material Safety Data Sheets |
| |
|
| Penetrating Oil |
| |
|
 |
Penetrates, loosens, and lubricates. May be used as a cleaner to remove tar and grease. Frees sticky parts, loosens rusted parts, protects metal surfaces from rust and corrosion. Easy to use and economical.
Competition: CRC, WD40 Product Description: Warren Penetrating Oil is a penetrate and lubricant as opposed to WD40, which is just a lubricant. Warren Penetrating Oil is a blend of fast acting super penetrating solvents that evaporate leaving a thin transparent protective film. Warren Penetrating Oil loosens rust and erosion almost instantly, it quickly penetrates into cracks, crevices and threads, freeing, bolts, lug nuts and other fasteners. Noticeable squeaks are silenced by friction – reducing lubricants. Warren Penetrating Oil may be used as a cleaner to remove tar, grease, oil adhesives and grimes, as it cleans it will also protect metals from rust and corrosion.
Warren Penetrating Oil has many automotive, home and mechanical applications. Spray liberally and allow to soak. To protect metal surfaces, do not wife off.
Material Safety Data Sheets |
| |
|
| Premium Starting Fluid |
| |
|
 |
Starts engines quickly for a fast start on the coldest days. Works on both diesel and gasoline engines and contains an upper cylinder lubricant that helps starting engines in all kinds of weather. Economical and easy to use.
COMPETITION: Gunk, Ig-Lo, Gold Eagle, McKay, Kar Products PRODUCT DESCRIPTION: Engine starting products are aerosol products, which sprayed into the carburetor or attached to an injection system, will assist starting engines, which may be bulky due to cold, dampness or under maintenance. Typically starting fluids consist of ethyl ether, blended with other petroleum hydrocarbon. How well a product dispenses the ether in cold weather is an important characteristic. Warren Starting Fluids are effective down to –65F, they have low freeze points, high vapor pressure at low temperatures, low flash point, high BTU content and an upper cylinder lubricant for protection. Warren Starting Fluid may be used with gasoline engines and some diesel engines. It is not recommended using any starting fluid in diesel engines that have glow plugs. Most passenger car and light truck diesel engines have glow plugs in order to preheat combustion chamber. The use of starting fluid in engines with glow plugs can cause serious engine damage and possible personal injury. Larger trucks and tractors may not have glow plugs. For example, some tractors do not have glow plugs and inject starting fluid directly into the manifold. Starting fluid works very well in this type of application.
Always consult the owner’s manual to determine the manufacturer’s recommendation and whether or not a specific vehicle is equipped with glow plugs. Follow the directions on the can when using any of Warren Starting Fluids.
Material Safety Data Sheets |
| |
|
| De-Icer |
| |
|
 |
Removes frost and ice from windshield, windows, locks & mirrors. Will Not Harm rubber, metal or paint finishes. Retards ice formations. Contains no CFC’s.
COMPETITION: Preston, Ig-Lo PRODUCT DESCRIPTION: Warren De-Icer is used to remove frost or ice from windshields. Warren De-Icer is an aerosol. Its active ingredient is methanol and additional ingredients being ethylene glycol, other alcohols and water. When the De-Icer is sprayed on, the methanol soaks into the frozen material and rapidly lowers its melting point. This allows the ice to become a soft, slush-like mixture even at below-freezing temperatures. This mixture can be applied in advance, it will retard ice formation and fogging on inside of windows.
TO REMOVE FROST AND ICE: Start vehicle and turn on defroster. Liberally spray windshield from top to bottom. Wait for ice or frost to thaw and remove by windshield wipers or a windshield-cleaning tool.
TO RETARD ICE FORMATION: Apply where desired prior to ice accumulation.
TO PREVENT FOGGING: Wipe inside windows with cloth dampened with Warren De-Icer.
TO THAW LOCK: Spray inside lock mechanism and on other moving parts of lock.
Material Safety Data Sheets |
| |
|
| Carburetor Cleaner |
| |
|
 |
Removes gum, varnish, sludge and carbon deposits. Instantly cleans carburetor linkage, PCV valves and chokes. Safe for oxygen sensors and catalytic converters. Contains no chlorinated solvents. Ozone safe and easy to use.
COMPETITION: Gumout, Radiator Specialty, Berryman.
PRODUCT DESCRIPTION: Vehicles with carburetors build up “sludge”, “varnish”, and other deposits due to poor combustion of fuel. These deposits reduce fuel combustion and cause valves to stick. All the linkages on a carburetor will stick causing the carburetor to run inefficiently. Warren Carburetor Cleaner is a blend of selected solvents, carefully formulated to maximize cleaning power. Difficult deposits are eliminated quickly. Use in well ventilated area. Insert extension tube into valve button. Avoid contact with car finish.
CARBURETOR AND LINKAGE: With engine off, remove air cleaner. Start engine and set at fast idle. Spray Warren Carburetor Cleaner on exterior surface of carburetor, including linkage. Also spray on short bursts around inside of carburetor. Allow engine to run for one minute and then repeat procedure for inside and outside of carburetor.
PCV VALVE: With engine off, disconnect hose from valve. Insert extension tube into valve opening and spray while working valve back and forth. Start engine and spray three or four short burst.
AUTOMATIC CHOKE: With engine off, spray ends of choke valve while opening and closing manually. Also spray piston and cylinder.
WARNING: This product is highly flammable and user should exercise caution.
Material Safety Data Sheets |
| |
|
| Engine Degreaser |
| |
|
 |
Good all-purpose degreaser. A blend of powerful solvents, surfactants and emulsifiers deep penetrating action to dissolve grease and oil can be safely used on all engines, lawn mowers and engine parts. Contains no CFC’s.
COMPETITION: Gunk, Engine Brite, Berryman
PRODUCT DESCRIPTION: Cleaning vehicle engines involves a variety of distict cleaning functions and several different types of products. Warren Engine Degreaser is one of the most common methods used for cleaning vehicle engines. Warren Engine Degreaser contains powerful solvents and surfactants to quickly penetrate grease, oil, dirt and grime. Warren Engine Degreaser also contains a grease cutter to loosen heavier build-ups. It is also self-emulsifying and contains no chlorinated solvents of CFC’s. Warren Engine Degreaser has a special stream nozzle that allows the user to direct the flow exactly where it is needed. For best results, scrape off heavy build-up of grease and grime first. Engine should be warm to the touch (NOT HOT – IF HOT, let engine COOL down for a few minutes), cover distributor and carburetor with plastic. Spray Warren Engine Degreaser directly onto warm engine, or surface tube to be cleaned. Allow the product to soak for a few minutes. Spray off residue with water using a hose. For really heavy build-up, some scrubbing may be necessary.
Material Safety Data Sheets |
|
| |
|
|
| |
|
|
